ForceField® Grout Sealant ASP
1.
Material Identification
Product Name: Grout Sealant ASP
Product ID: F GSASP
Chemical Family: Aqueous dispersion of partially fluorinated
products
NPCA-HMIS Rating:
Health 1
Flammability 0
Reactivity 0
Personal protection rating to be
supplied by user depending on use conditions.
2. Hazardous Ingredients
Ethylene Glycol
Monobutyl Ether, CAS 111-76-2, 1%
Isopropanol, CAS
67-63-0, 1%
3. Physical Data
Density:
1.01+/- 0.02
pH: 7.0 +/-
1.0
Water Solubility:
Dispersible
Boiling Point:
100 degrees Centigrade
Appearance:
Clear, pale yellow solution
Odor: Mild
4. Fire and Explosion Data
Flash Point:
Greater than 200 Fahrenheit by PMCC
Extinguishing
Media: water spray, foam, dry chemical or carbon dioxide
Special
Procedures: Evacuate personnel to a safe area, avoid
breathing decomposition products, fire fighting personnel
should wear respiratory protection.
Unusual Hazards:
Emits toxic and corrosive fumes when burned.
5.
Reactivity Data
Chemical
Stability: Stable
Incompatibility:
Avoid contact with strong oxidizers.
Polymerization:
Will not occur.
Decomposition:
Thermal decomposition may produce oxides of carbon and
nitrogen, and toxic fluorinated decomposition products.
6. Health Information
Toxicity:
Not established
Carcinogenicity:
None of the components present in this material are listed by
IARC, NTP, or OSHA.
Exposure Limits:
Not established
Safety
Precautions: Avoid contact with eyes, skin, and
clothing. Do not aerosolize. Wash thoroughly after handling,
especially before eating, drinking, or smoking.
7. Employee Protection
Engineering
Controls: Use adequate ventilation. Vent fumes outside
work area. Use NIOSH approved respirator if airborne
concentrations pose a health hazard. Emergency showers and
eye washes should be available in work area. Do not
aerosolize. Avoid Misting and Overspray. Always provide good
ventilation. Use only low pressure sprayers (less than 60 psi).
Never use a “power painter” as they generate high pressure and
aerosolize product.
Eye Protection:
Wear safety glasses or goggles.
Skin Protection:
Wear impervious gloves and clothing suitable to prevent skin
contact.
Other: Do
not consume food, drink, or tobacco in areas where they may
become contaminated by this material. Always wash hands
thoroughly with soap and water before eating, drinking, and
smoking.
8. First Aid
Inhalation:
Remove to fresh air. If not breathing, give artificial
respiration. If breathing is difficult or respiratory tract
is irritated, consult a physician.
Skin Contact:
Remove contaminated clothing. Flush skin with mild soap and
water.
Eye Contact:
Flush eyes with plenty of water for at least 15 minutes and
consult a physician if irritation persists.
Ingestion:
Consult a physician.
9. Disposal Information
Spill, Leak, or
Release: Contain spill and salvage as much material as
possible. Pick up remaining product with absorbent.
Waste disposal:
Dispose of product only by methods approved by federal, state,
and local regulations.
10. Storage
Store in a cool
well ventilated area. Keep container tightly closed. Do not
freeze.
11. Transportation
DOT Proper Shipping
Name: Not Regulated
DOT/IMO Proper
Shipping Name: Not Regulated
This
information relates only to the specific material designated
herein and does not relate to use in combination with any
other material or in any process. Such information is to the
best of our knowledge and belief, accurate and reliable as of
the date compiled. However, no representation, warranty or
guarantee is made as to its accuracy, reliability, or
completeness. It is the user’s responsibility to satisfy
himself as to the suitability and completeness of this
information for his own particular use. We do not accept
liability for any loss or damage that may occur from the use
of this information nor do we offer warranty against patent
infringement.
Last Revision Date:
07/01/04 Preparer:
R. Lasnik, Vice President
|
